06Nov

Fireproofing in high-rise buildings helps protect structural stability and supports safe evacuation during a fire. With occupants located many stories above ground, evacuation and firefighting operations can take longer than in smaller buildings. Properly designed fire protection gives occupants and emergency responders critical time.

An effective strategy combines structural fireproofing, fire-resistant compartments, protected escape routes, and active systems such as sprinklers and alarms. Together, these measures help limit damage and reduce the risk of structural failure.

What Is a High-Rise Building?

Under the 2021 International Building Code (IBC), a high-rise building has an occupied floor located more than 75 feet above the lowest level of fire department vehicle access.

Height creates challenges that influence fire protection design, including:

  • Longer evacuation routes for occupants on upper floors.
  • More difficult access for firefighters and equipment.
  • Complex water-supply and pressure requirements.
  • Potential smoke movement through stairs, shafts, and other vertical openings.
  • Greater demands on emergency communication and power systems.

The applicable requirements depend on the locally adopted code edition, amendments, occupancy, construction type, and building configuration. The 2021 IBC references in this article are a framework—not a substitute for project-specific code review.

Why Is Fireproofing Essential in High-Rise Buildings?

Protecting Load-Bearing Structures

Noncombustible materials are not automatically fire-resistant. Structural steel, for example, can lose strength and stiffness as temperatures rise, even though it does not burn.

Fireproofing insulates structural members and delays heat transfer, helping them maintain their load-bearing function for the required fire-resistance period under standardized test conditions.

Supporting Evacuation and Rescue

High-rise occupants may need to travel considerable distances to reach safety. Structural protection, enclosed stairs, and fire-resistance-rated assemblies work together to support evacuation and emergency response.

Structural fireproofing does not directly stop smoke movement. That role depends on other measures, including compartmentation, protected openings, and applicable smoke-control systems.

Limiting Fire Spread and Property Damage

Fire-rated walls, floors, doors, and penetration protection help contain a fire within defined areas. Maintaining these barriers can reduce damage beyond the area of origin and protect critical routes through the building.

Passive and Active Fire Protection: How They Work Together

High-rise fire safety relies on both passive and active protection. Neither should be treated as a replacement for the other.

Passive Fire Protection

Passive systems are built into the structure and its assemblies. Examples include:

  • Spray-applied fire-resistive materials on structural members.
  • Intumescent coatings for structural steel.
  • Fire-resistance-rated walls, floors, and shaft enclosures.
  • Fire doors and protected openings.
  • Firestop systems at penetrations and joints.
  • Perimeter fire containment at floor-to-exterior-wall interfaces.

These systems help maintain structural capacity or restrict the passage of fire and smoke, depending on their function.

Active Fire Protection

Active systems detect, communicate, or respond to a fire. Depending on applicable requirements, they include:

  • Automatic sprinklers.
  • Standpipes and fire department connections.
  • Fire detection and alarm systems.
  • Emergency voice communication systems.
  • Portable fire extinguishers.
  • Smoke-control or smoke-removal systems.
  • Fire pumps and associated power supplies.

Emergency and standby power support designated life-safety systems when normal power is unavailable.

Common High-Rise Building Fireproofing Methods

1. Spray-Applied Fire-Resistive Materials

Spray-applied fire-resistive materials (SFRM) provide an insulating layer around steel beams, columns, and other components covered by a tested design. Products include cementitious and sprayed-fiber materials.

SFRM is commonly used where the structure will be concealed or a decorative finish is unnecessary.

Its performance depends on:

  • The applicable tested and listed assembly.
  • Required material thickness and density.
  • Substrate condition and compatibility.
  • Adhesion and cohesion.
  • Correct application and curing conditions.
  • Protection from damage after installation.

High-rise buildings can also require enhanced SFRM bond strength. These requirements help address the material’s ability to remain attached to the protected substrate.

2. Intumescent Fire-Resistive Coatings

Intumescent coatings expand when exposed to sufficient heat, forming an insulating char layer that slows heat transfer to steel.

Often selected for exposed architectural steel, these coatings can maintain the visibility of structural features while providing the protection required by a listed design.

Intumescent products are not all epoxy-based. Available systems include water-based, solvent-based, and epoxy formulations, each with specific application and service limitations.

Important selection factors include:

  • Required fire-resistance rating.
  • Steel member size and configuration.
  • Interior or exterior exposure.
  • Primer and topcoat compatibility.
  • Required dry-film thickness.
  • Inspection and maintenance needs.

Fire-resistance ratings apply to specific protected members or assemblies—not to a coating independently of its installation. Do not assume a product provides a particular hourly rating on every steel section.

3. Fire-Resistant Board and Gypsum Assemblies

Board systems can protect structural members or form part of rated walls, ceilings, and shaft enclosures.

Type X gypsum board, addressed by ASTM C1396, is commonly used in fire-resistance-rated construction. However, a Type X label alone does not establish the rating of a completed wall or ceiling.

Performance depends on the complete assembly, including board thickness, number of layers, framing, fasteners, joints, and installation details.

4. Concrete Encasement

Concrete encasement can provide fire protection for structural steel where supported by the applicable design. Its weight, dimensions, construction sequence, and architectural impact must be considered.

It may be appropriate where durability and robust physical protection are priorities.

Key IBC Requirements for High-Rise Fire Protection

Section 403 of the 2021 IBC addresses high-rise buildings. Other relevant provisions cover construction types, fire-resistance ratings, means of egress, fire protection systems, and special inspections.

Enhanced SFRM Bond Strength

High-rise provisions establish increased minimum bond-strength requirements for SFRM, with a higher threshold for buildings exceeding 420 feet.

Bond strength does not replace required thickness, density, or assembly compliance. All applicable requirements must be satisfied.

Protected and Separated Exit Stairways

Exit stairs require appropriate enclosure and separation so that a single incident is less likely to compromise multiple escape routes.

For certain buildings more than 420 feet in height, the 2021 IBC requires an additional interior exit stairway, subject to occupancy exceptions and provisions involving qualifying occupant evacuation elevators.

An additional stairway is not a universal requirement for every high-rise building.

Fire Service Access Elevators

Under the 2021 IBC, buildings with an occupied floor more than 120 feet above the lowest level of fire department vehicle access generally require at least two fire service access elevators, or all elevators where fewer than two are provided.

These elevators must satisfy specific protective and operational requirements. They are not simply ordinary passenger elevators designated for emergency use.

Construction Type and Fire-Resistance Ratings

Construction types influence allowable height, area, materials, and required protection.

Many high-rise projects use Type I construction, although permitted approaches depend on the applicable code and project conditions. Certain mass-timber construction types also permit taller buildings within defined limits.

The necessary fire-resistance rating must be established through code analysis—not assumed solely from the building’s height.

SFRM Installation Requirements

Section 704.13 of the 2021 IBC addresses SFRM installation. Proper application requires compliance with the approved design and manufacturer’s instructions.

Prepare the Substrate

Surfaces must be free of conditions that interfere with adhesion, such as dirt, oil, grease, loose scale, and unsuitable coatings.

Primers, paints, and encapsulants must meet applicable compatibility and bond requirements.

Follow the Listed Design

Installers must follow specified requirements for:

  • Minimum thickness and dry density.
  • Application methods.
  • Bonding agents.
  • Reinforcement or accessories.
  • Substrate conditions.
  • Other components required by the listing.

Maintain Suitable Application Conditions

Temperature, ventilation, and drying conditions affect installation quality. Follow the applicable code provisions and manufacturer’s requirements before, during, and after application.

Repair Defects and Damage

Cracks, voids, delamination, exposed substrate, and damage from subsequent construction activities require evaluation and correction.

Fireproofing should remain continuous wherever required by the approved design.

Special Inspections and Quality Assurance

Inspection helps verify that installed protection matches the approved system.

Under the 2021 IBC:

  • Section 1705.15 addresses special inspections and testing of SFRM.
  • Section 1705.16 addresses special inspections of mastic and intumescent fire-resistant coatings.

SFRM inspections address matters such as substrate preparation, application conditions, thickness, density, and bond strength.

Inspection of applicable intumescent systems follows AWCI 12-B, alongside relevant project and manufacturer requirements.

Inspection is especially important before fireproofing becomes concealed. Repairs, later alterations, and penetrations also need appropriate oversight to preserve the building’s protection.

How to Choose the Right High-Rise Fireproofing System

The best solution balances code compliance, tested performance, durability, appearance, and installation requirements.

Project considerationSelection priority
Concealed structural steelA suitable listed SFRM or other approved protection system
Exposed architectural steelFinish quality and listed intumescent coating options
Moisture or exterior exposureProducts approved for the expected environment
Areas vulnerable to impactDurable systems or suitable protective measures
Required fire-resistance ratingA matching tested design for the specific member or assembly
Construction scheduleAccess, application conditions, drying, and inspection
Long-term performanceMaintainability and repair procedures

Different systems may be used within the same building. However, combining materials on a single structural member requires an approved design or evaluation; the systems should not be assumed interchangeable.

Frequently Asked Questions

Does fireproofing make a high-rise building fireproof?

No. Fireproofing improves fire resistance but does not eliminate fire risk. Building safety depends on coordinated structural protection, compartmentation, suppression, detection, evacuation planning, and maintenance.

Is intumescent coating better than spray-applied fireproofing?

Neither is universally better. Intumescent coatings are often preferred for visible steel, while SFRM is commonly selected for concealed areas. The correct choice depends on the listed design, environment, finish, cost, and durability requirements.

Do all high-rise buildings need the same fire-resistance rating?

No. Required ratings vary with construction type, occupancy, structural element, and applicable code provisions. Height is one factor, not the sole determinant.

Does fireproofing need maintenance?

Yes. Leaks, impacts, renovations, and equipment installations can damage fireproofing or compromise rated assemblies. Damage should be assessed and repaired using approved procedures.

Protect High-Rise Buildings With a Coordinated Fire Safety Strategy

Effective high-rise building fireproofing starts with the right design and continues through installation, inspection, and maintenance. Structural protection must work alongside fire-rated compartments, protected escape routes, and reliable active systems.

Planning a high-rise project or evaluating existing fireproofing? Contact our team to discuss system selection, inspection needs, and project-specific fire protection requirements.

Code reference: International Code Council, 2021 International Building Code, Sections 202, 403, 704.13, 1705.15, and 1705.16, and Chapter 25. Verify all requirements against the edition and amendments adopted by the local authority having jurisdiction.

Leave a Reply

Your email address will not be published. Required fields are marked *